Request Free Estimate

 

What're your opinions regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Installing a bathtub isn't specifically brain surgery, however it does require solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old tub with a new one is also a reasonably hard project. If the old bathtub is readily available, the project can relocate easily; if you need to open a wall surface to get rid of the old tub and place the brand-new bathtub, the task is much harder. In either case, the project is within a house handyman's skills, although you will certainly require a helper to move out the old tub and also embeded in the new one. See to it you have certified on your own for the task and are comfortable trying it. Instead of employing a professional to take control of a halfway-completed project, it is better to consider utilizing one before you begin. Possibilities are you might require an expert plumber to make tube links.
This post will aid you install a brand-new bathtub in your shower room if you have already gotten a brand-new tub as well as do not require to transform the arrangement of your previous water supply pipes.
Your tools as well as product list should comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Planning for the Installment

To start with, the sustaining framework supplied with the bathroom needs to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to avoid pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of both faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its final position.

 

 

Removing Old Taps

If you need to change old faucets with new ones as a part of your setup, then the first thing you ought to do is separate the water. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be rather bothersome due to the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. When the supply pipelines have actually been eliminated, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from transforming during this procedure. When the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.

 

 

Setting up the Bathtub

Utilizing the two wood boards under its feet, place the bath tub in the called for setting. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also readjusting the feet on the tub until the spirit level reads degree.
To set up faucets, fit all-time low of the outermost versatile faucet port to the ideal supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Activate the water and also examine all joints and new pipework for leakages and tighten them if essential. Load the bath tub as well as also check the overflow outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the producer's instruction manual. Tiling and also sealing around the bathtub must wait up until the tub has been utilized at the very least when as this will certainly settle it right into its final setting.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in place between the faucet and also the sink. Secure the tap in place with the maker given backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind needs to be linked to the tap ends first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Tub

In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to split a stiff seal, triggering the water to penetrate the wall surface between the bath and the tiling, leading to issues with wetness and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes as well as cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to allow for the movement experienced when the tub remains in usage. The sealant can fracture relatively early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant sticky and grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I am very fascinated with A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed my piece. Do you know about someone else who is in to the subject? Feel free to promote it. Bless you for your time. Visit us again soon.

Immediate response? Click here.